| Inventory | Construction
The yacht's hull was fabricated from 1/8 inch thick cedar laminates. Each layer got epoxy glued 90 degrees to each other and wrapped around to include the deck, in essence creating a structure that is a continuous and seamless sheet of plywood. Strategic high load areas near the mast bulkhead and the keel are reinforced with carbon fiber between the laminates. There are 10 layers of veneer besides the 5/16 inch thick tongue and groove mold that is visible throughout the interior, including the extreme bow and stern, as well as every part of the bilge. The interior mold is epoxy saturated and Linear Polyurethane varnished throughout the ship. All bulkheads are foam filled, plywood sided and finished with varnished epoxy coated tongue and groove cedar veneer. The keel was fabricated in form of a steel jacket fastened over a welded internal structure that is 11-feet tall. The bottom of it was hot poured with 30,000 pounds of lead, and the upper portion of the keel foil serves as a fuel tank holding 200 gal. of diesel. The cabin sole is constructed from scarfed and laminated oak beams. Individual panels of 1/2 inch plywood fit in between and are easily removed for instant access to all locations in the bilge. The foot of the mast terminates in the forward shower. Any rain or green water that penetrates the structure through the halyard or sheave slots of the extrusion is being expelled through the shower sump. Hauled in 2004 when the bottom was sanded wet and dry, and painted the airless method with 3-coats of Z-Spar AB-90 . The sides were buffed, polished and waxed
Mechanical Equipment
A 250 HP Turbo charged Cummings Diesel Engine with a Borg Warner Transmission provides propulsion under power at 10 kts, 2,300 rpm, using 7 galls of fuel per hour, or 5 galls of fuel per hour at 8 knots. The transmission's output shaft connects to a Morse chain drive unit that terminates 3 ft below into the keel. From that point, a 2 shaft drives a Martec folding propeller. The shaft is short and roller bearing supported on each end for vibration-free operation. The bearings and chain are lubricated via an oil sump, also in the keel and don't require any maintenance. Without any sails, just powered by the engine, the yacht cruises 10 kts at 2300 rpm using 7 gal. of fuel per hour, or 5 gal. per hour at 8 kts. 3 banks of deep-cycle batteries (10 batteries were replaced within the previous year) 5000 watt Northern Lights diesel generator with dual pack sound insulation . Watermaker by Village Marine Tech (New).
Accommodation
Below decks are 17 berths, of which are wide enough to sleep 2 people. The owner's stateroom features an oversize queen bed with private head & shower area, large hanging locker, lots of storage, TV and CD player with surround sound. There are 2 additional bathrooms and a large shower, as well as a very sizable hanging locker and lots of storage space throughout the vessel. The galley is well thought out and includes a horizontal freezer, an upright fridge and freezer, a three-burner Stainless stove & oven and a large SS double sink
Electronics
Data Marine Offshore electronics package is hardwired to a Swiss GPS computer and a DEL computer with a 17 flat NEC high resolution monitor used for the electronic chart system. The entire electronics system is linked together with NMEA 0183
Sails and Rigging
Extruded aluminum mast extends 130 ft. above the water line. The boom has a fixed clew, and moves away from the mast hydraulically to flatten the sail. SAILS:- (Lidgard, NZ) (1) 2-ply Mylar full battened mainsail. (1) Mylar # 1 genoa (1) 2-ply Mylar # 3 genoa (1) Mylar 165% reacher (1) Nylon 110ft. Asymmetric spinnaker (1) Mylar tallboy (1) Mylar staysail to go with the reacher There is also at least 10 other assorted spinnakers, as well as a reacher and other mainsails and genoas , all stated to be in excellent condition. ROD RIGGING, custom designed by NAVTEC. WINCHES:- 4 Primary Barient grinders interconnected by three pedestals. 9 other various winches.
Comments
Built over a period of 7 years with the help of a collection of dedicated and highly skilled crafts men, guided by Peter Ebbutt, a well known Naval Architect and Structural Engineer, who kept the project on the proper path. The result of that effort has exceeded my highest and very ambitious expectations. She handles beautifully... in choppy waters, high wind and lazy breezes. The boat performs completely balanced with outstanding control. Should the wind gods fail to smile on us, our reliable turbo-charged Cummings power plant propels us to our destination. Below decks are 17 beds... of them are wide enough to sleep 2 people. In addition, there is an owner's cabin with a large hanging locker, oversize queen bed, bathroom, shower, lots of storage, TV, CD player and surround sound. All the accommodations you would ever want. She is beautiful and ready for a new owner. Errichtet ine Zeitdauer von 7 Jahren mit Hilfe einer Ansammlung engagierter und in hohem Grade erfahrener Fertigkeitmer, gefon Peter Ebbutt, ein weithin bekannter Marinearchitekt und ein struktureller Ingenieur, die das Projekt auf dem korrekten Weg hielten. Das Resultat dieser Bemhat meine hten und sehr ehrgeizigen Erwartungen iegen. Construido en un periodo de 7 acon ayuda de un interminable equipo dedicado y altamente cualificado, guiados por Peter Ebbutt, un renombrado Arquitecto Naval e Ingeniero Estructural quien mantuvo el proyecto en la linea correcta. El resultado de ese esfuerzo ha superado las expectaciones mas altas.
|
